Your list is empty, add products to the list to send a request
Close
System Sensor 2151 Smoke Detector For Special Application
System Sensor 2151 can be used as a pendant mount detector in no-flow/low-flow air-handling systems (0-3,000 FPM). The pendant /plenum mounted 2151 is to be installed into a B114LP or B114LPBT base. This is the perfect combination for installation in ducts where the air velocity is below 500fpm or for duct sizes as small as in diameter.
Close
System Sensor 22051E-26 Photoelectric Smoke Detector
System Sensor 22051E-26 photoelectric smoke detector has a completely new detection chamber design, the result of many years of research and design by System Sensor. This delivers improved responsiveness, reduced sensitivity changes caused by settling the dust and reduced false alarms resulting from insect ingress and other debris. The revolutionary Series 200 Advanced range delivers a totally new detector platform that incorporates the new digital Series 200 Advanced Protocol.
Close
System Sensor 22051TE Photoelectric Smoke / Thermal Multi-Criteria Fire Detector
System Sensor 22051TE multi-criteria multi-sensor Photo Thermal detector uses thermal assistance to the core photoelectric smoke detector to give enhanced false alarm immunity and faster response to a wide range of incipient fires. The plug-in unit combines two separate sensing elements that are managed by embedded software to act as a single unit. The 22051TE conforms to EN54-5, a 58°C fixed temperature and rate of rise thermal, with the smoke detection element conforming to EN54-7. The sensing elements of the 22051TE are panel controllable so the sensitivity thresholds of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.
Close
System Sensor 52051E Fixed Temperature Analogue Addressable Heat Sensor
System Sensor 52051E Fixed Temperature Analogue Addressable Heat Sensors employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing. Their linear response allows these sensors to be used to signal temperatures over the range of 58°C (Class A1S) to 78°C (Class BS). The 52051RE uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10°C/minute (typical) or if the temperature exceeds a threshold of 58°C (Response Class A1R).
Close
System Sensor 52051HTE-26 High Temperature Analogue Addressable Heat Sensor
System Sensor 52051HTE High Temperature Analogue Addressable Heat Sensors employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing. Their linear response allows these sensors to be used to signal temperatures over the range of 58°C (Class A1S) to 78°C (Class BS). The 52051RE uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10°C/minute (typical) or if the temperature exceeds a threshold of 58°C (Response Class A1R).
Close
System Sensor B501AP Analogue Detector Standard Base(white)
System Sensor B501AP Analogue Detector Standard Base(white) are designed for use with all System Sensor 500, 200, 200+ and 200 Advanced intelligent ranges of sensors and their variants (Note: If the B524HTR is used with 200 Advanced Isolator sensors, the isolator feature will not function). The standard B501AP is white, an IV suffix indicates the base is ivory in colour, a BK suffix indicates the base is black.
Close
System Sensor M200E-SMB Surface Mount Module Box
The new family of input/output modules forms part of System Sensor Europe's Series 200 plus family. Single and multi-way models are available within the same mechanical package, reducing both the cost of installation and the mounting space required.
Their unique mechanical design allows each module to be mounted in either a wall box, on a DIN rail or within any type of enclosure. Irrespective of the mounting methods chosen, the address switch is both visible and accessible for selection.
To facilitate the interconnection of DIN rail mounted modules, packs of pre-cut and stripped lengths of wire are available.
Close
System Sensor M201E-240 Output Control Module For 240VAC Loads
The M201E-240 and M201E-240-DIN form part of the new family of input/output modules in System Sensor Europe's Series 200 plus range. Each module has built-in short circuit protection for the communications loop; however, to increase application flexibility, the isolators can be selected/deselected on an individual module basis.
The M201E-240 is a loop-powered device controlling an unsupervised double pole (one normally open, one normally closed) output suitable for managing 240VAC loads.
Close
System Sensor MCP5A-RP01FG-01 Addressable Manual Call Point
This System Sensor Call Point Break Glass Unit MCP5A-RP01-FG01 is specifically designed to be used on System Sensor Fire Alarm Control Panels. The unit is designed to give a manual signal to the Sensor System Fire Alarm Control panel which will operate the fire alarm system.
These units are based on the industry standard KAC manual call point. They have been designed specifically to give installation efficiency, flexibility and compliance with the latest standards.
The System Sensor Manal Call Point Break Glass MCP5A-RP01-FG01 features an Integral LED. This LED will illuminate once the break glass unit has been operated. This feature allows easy identification as to which System Sensor Manual Call Point Break Glass has been operated.
Close
System Sensor OSY2 Sprinkler Supervisory Switch
System Sensors OSY2 Supervisory Switch is used to monitor the open position of an Outside Screw and Yoke (OS&Y) type gate valve. The OSY2 consists of a rugged housing, intended for indoor and outdoor use. When installed with the actuator in the vertical position, the OSY2 is NEMA 3R rated per UL.
Close
System Sensor P056 KAC Seal for Call Point Cover
KAC Callpoints are the leaders in Call Point manufacture, invented by KAC over 40 years ago they have constantly driven to improve both standards and design of the call point to this day.
Close
System Sensor PS200 KAC Hinged Call Point Cover
KAC Call points are the leaders in Call Point manufacture, invented by KAC over 40 years ago they have constantly driven to improve both standards and design of the call point to this day.
